One that keeps up with 15.2 CFM at 26 PSI continuously. Fuji’s kit includes an inlet pressure regulator with gauge. It’s a compressor gun: run it on shop air, not a Fuji turbine.
Ships from Fuji Spray. Allow a few extra business days.
The Fuji Spray LX-20 is the HVLP gun in the X Series — a general-purpose compressor gun built to replace a conventional high-pressure gun in professional finishing, from woodworking to bathtub resurfacing. Side-mounted fan pattern control gives precise, reduced-overspray adjustment up to a 330 mm (13") fan, and 100% stainless steel fluid passages handle waterborne and solvent-based coatings from thin dyes to high-solid clears. At 502 g it is light in the hand, and it uses the same familiar controls as a conventional gun, with faster application and higher transfer efficiency.
It ships with the 1.4 mm air cap set installed, with five sizes from 1.0 mm to 2.0 mm available to match the material. Fuji's kit also includes the 1.2 mm and 1.7 mm sets and an inlet pressure regulator with gauge, so the gun is ready for a clear coat, a sealer, or a heavier build without a second purchase.
This is the pressure-feed LX-20: a 3/8" fluid inlet in place of a cup, fed from a pressure pot for large jobs and heavy material. It is sold as the gun only. For a cup-fed gun, see the gravity-feed LX-20.
📄 LX-20 HVLP Spray Gun Specification Sheet.
📄 LX-20 Spray Gun User Manual.
To use this gun with the 3M Paint Preparation System (PPS) 2.0, you'll need the S18 Adapter (#MMM26054), sold separately. Compressor guns take 3M's standard PPS 2.0 cup straight off the fluid coupler. Run the Large or Midi hard cup from a Cup Kit, by the size of the job — the Large for a bigger project, the Midi for a smaller one. Fuji’s own how-to shows the same adapter-and-cup install on a V8.
3M PPS 2.0 · fits this gun
This gun takes the S18 adapter (MMM26054) and the standard PPS 2.0 hard cup from a Cup Kit. No High Output cup is needed on a compressor gun.
Each Cup Kit has 50 liners, 50 lids with 200 micron filters, 32 sealing plugs and the hard cup. The adapter is sold separately.
Fitting tip: drop a liner into the hard cup, lid it, then push the gun onto the lid and give it a quarter turn. Watch Fuji's install video
Key Features
Compatible Air Cap Sets
This gun also takes:
What's in the Box
Consumables
| Gun Type | HVLP |
| Feed Type | Pressure Feed |
| Air Source | Compressor |
| Application Type | Waterborne and solvent-borne high-solid clear coat |
| Standard Air Cap Set | 1.4 mm |
| Available Air Cap Sets | 1.0, 1.2, 1.4, 1.7, 2.0 mm |
| Air Supply Pressure | 26 PSI at gun inlet (1.8 bar) |
| Air Consumption | 15.2 CFM |
| Maximum Fan Width | 330 mm (13 in) |
| Air Inlet Size | 1/4" BSP and NPS |
| Air Supply Hose | 5/16" ID |
| Fluid Passages | Stainless steel |
| Gun Weight (Without Cup) | 502 g (17.7 oz) |
| Compliance | VOC compliant |
| Fluid Coupler | 3/8" x 19P |
| Fluid Supply | Pressure pot |
Country of Origin
Designed and assembled in Canada.
Fuji filmed this on a V8 with its S15 adapter; the gravity-feed LX-20 takes the S2 adapter on the same style of fluid coupler, so the steps are similar.
